Видео

Terrible lighting

Brother I know this video is old, but I really love the way you position the camera is really easy to see the work your doing and give the perfect example of how to do it 🫡

upstream sensors get lazy and start to fail throwing the downstream code.....You'll notice other codes or your car doesn't run as it should do to the air/fuel ratio being off.....the ECU will dump fuel thinking it's lean.....

how were you able to buy a complete rear bedside like that is that aftermarket ? i have a 2024 chevy in my shop now and the ins co says they only have a outer skin to allow me to put on

I use a heat gun to soften the panel glue so the skin comes off easier. Most panels are bonded now. Great job.

Where did you get the replacement quarter panel? The only ones I can find are either the entire side of the car (from Classic Industries) or they are much shorter going up the pillars.

How much does the panel cost

Great idea to mix and match. To do it though, you don’t have to pop out the lock. Just push it down. When it clicks you can swap them out and then pop it back up to lock it.

U have to make use of coolant for that to stop

Thanks mate. Needed this info to do a customers car. Thanks again from 🇦🇺🇦🇺🇦🇺🇦🇺

Horse shit. Absolute BS.

Interesting that a 3 year old car has a bad O2 sensor. I have a 2015 GT with 17,000 miles and never had one issue.

There's a rubber seal that runs along the daytime running lights. The rubber seal on the outerside came off or came out of place. How do I fix it myself?

and here i was only been using my midget slim 3 inch flat screw 🤣🤣🤣 multi purpose actualy

Or you could just use some good old needle nose pliers if you have some

Matco has them

You can still get it from Matco DLR20. its 12 bucks.

Hate IA voice

It's no longer made, called lisle last week as mine broke

Where to buy this tool i need pne

Hate to ask this here but do you think this would work on a 2020 Camaro SS? Thanks again

Thumbs up.

How much did you charge?

You said your check engine light came on, did it throw any specific codes? My wrench light is coming on and the weld on my clutch assembly broke. Wondering if this is causing the limp mode?

yeah, but if it's removed this way how do you reinstall?

Very helpful vid but damn the background music 🤧

can u do mine next? same panel needs replaced and then some...

Do you have any tips for removing that chrome molding / DRL strip? Is there a standard process as to not damage the clips? I have to replace the DRL on my 2023 Sonata and the clips are the only thing sketching me out.

Do u know if that same identical bumper will bolt on and fit right in on a 16 silverado??? Want to do a dual exhaust and with that bumper. Thank u in advance

Where you guys located

Dude if I could like your vid a thousand times I would. All the other vids show guys just ripping the bumper off and I cringe every time. I wish everyone would follow your instruction to reduce the chance of those cheap plastic clips breaking. I'm currently taking off my bumper for the 4th time and looking up your video for the 4th time to get it exactly right.

Me today 😅

Thank you, that was just what i was looking for!

Great video super helpful thank you.

So ur grinding away the spot welds?

Is this how you remove the grill to do you have a video for it

can this be done if the if the supports in the shell are bent at all? Is there any way you would you be able to tell without taking the skin off?

Did you just screw the new bedside on?

Can you tell me where and what size wheel your using on the angle grinder ! Thanks

If you don't mind what size disc or wheel is that on your angle grinder? I would like to try that out i always use a belt sander but that wheel you have looks faster! Thanks

Chinga ball joint !

That’s ridiculous they make the bed that way.

Well now I know I’m better off just getting a whole bed rather than repairing the panel

You made it simple. Thanks

Where did you buy the quarter, I can only find entire side panels.

They make a heel dolly made out of rubber that works GREAT

Donyou have to remove the bumber? Im about to start doing this

Did you weld the new one back in?

Bom trabalho de reparo.

Sir, great work. What was the estimated cost to do this work? I had a deer hit right side of truck bed. I think the outer skin needs to be replaced, but the body shop says they have to remove both inner and outer panel. Your thoughts